Airborne Lidar Measurements of XCO2 in Synoptically Active Environment and Associated Comparisons With Numerical Simulations.

Frontal boundaries have been shown to cause large changes in CO2 mole-fractions, but clouds and the complex vertical structure of fronts make these gradients difficult to observe. It remains unclear how the column average CO2 dry air mole-fraction (XCO2) changes spatially across fronts, and how well airborne lidar observations, data assimilation systems, and numerical models without assimilation capture XCO2 frontal contrasts (ΔXCO2, i.e., warm minus cold sector average of XCO2). We demonstrated the potential of airborne Multifunctional Fiber Laser Lidar (MFLL) measurements in heterogeneous weather conditions (i.e., frontal environment) to investigate the ΔXCO2 during four seasonal field campaigns of the Atmospheric Carbon and Transport-America (ACT-America) mission. Most frontal cases in summer (winter) reveal higher (lower) XCO2 in the warm (cold) sector than in the cold (warm) sector. During the transitional seasons (spring and fall), no clear signal in ΔXCO2 was observed. Intercomparison among the MFLL, assimilated fields from NASA's Global Modeling and Assimilation Office (GMAO), and simulations from the Weather Research and Forecasting--Chemistry (WRF-Chem) showed that (a) all products had a similar sign of ΔXCO2 though with different levels of agreement in ΔXCO2 magnitudes among seasons; (b) ΔXCO2 in summer decreases with altitude; and (c) significant challenges remain in observing and simulating XCO2 frontal contrasts. A linear regression analyses between ΔXCO2 for MFLL versus GMAO, and MFLL versus WRF-Chem for summer-2016 cases yielded a correlation coefficient of 0.95 and 0.88, respectively. The reported ΔXCO2 variability among four seasons provide guidance to the spatial structures of XCO2 transport errors in models and satellite measurements of XCO2 in synoptically-active weather systems.

Atmospheric CO(2) column measurements in cloudy conditions using intensity-modulated continuous-wave lidar at 1.57 micron.

This study evaluates the capability of atmospheric CO2 column measurements under cloudy conditions using an airborne intensity-modulated continuous-wave integrated-path-differential-absorption lidar operating in the 1.57-µm CO2 absorption band. The atmospheric CO2 column amounts from the aircraft to the tops of optically thick cumulus clouds and to the surface in the presence of optically thin clouds are retrieved from lidar data obtained during the summer 2011 and spring 2013 flight campaigns, respectively. For the case of intervening thin cirrus clouds with an average cloud optical depth of about 0.16 over an arid/semi-arid area, the CO2 column measurements from 12.2 km altitude were found to be consistent with the cloud free conditions with a lower precision due to the additional optical attenuation of the thin clouds. The clear sky precision for this flight campaign case was about 0.72% for a 0.1-s integration, which was close to previously reported flight campaign results. For a vegetated area and lidar path lengths of 8 to 12 km, the precision of the measured differential absorption optical depths to the surface was 1.3 - 2.2% for 0.1-s integration. The precision of the CO2 column measurements to thick clouds with reflectance about 1/10 of that of the surface was about a factor of 2 to 3 lower than that to the surface owing to weaker lidar returns from clouds and a smaller CO2 differential absorption optical depth compared to that for the entire column.

Super-resolution technique for CW lidar using Fourier transform reordering and Richardson-Lucy deconvolution.

An interpolation method is described for range measurements of high precision altimetry with repeating intensity modulated continuous wave (IM-CW) lidar waveforms using binary phase shift keying (BPSK), where the range profile is determined by means of a cross-correlation between the digital form of the transmitted signal and the digitized return signal collected by the lidar receiver. This method uses reordering of the array elements in the frequency domain to convert a repeating synthetic pulse signal to single highly interpolated pulse. This is then enhanced further using Richardson-Lucy deconvolution to greatly enhance the resolution of the pulse. We show the sampling resolution and pulse width can be enhanced by about two orders of magnitude using the signal processing algorithms presented, thus breaking the fundamental resolution limit for BPSK modulation of a particular bandwidth and bit rate. We demonstrate the usefulness of this technique for determining cloud and tree canopy thicknesses far beyond this fundamental limit in a lidar not designed for this purpose.

High-resolution CW lidar altimetry using repeating intensity-modulated waveforms and Fourier transform reordering.

An interpolation method is described for range measurements of high precision and altimetry using repeating intensity-modulated continuous wave (IM-CW) lidar waveforms, where the range is determined by means of a cross-correlation between the digital form of the transmitted signal and the digitized return signal collected by the lidar receiver. This method uses reordering of the array elements in the frequency domain to convert a repeating synthetic pulse signal to single highly interpolated pulse. The computation of this processing is marginally greater than the correlation itself, as it only involves reordering of the correlation in the frequency domain, which makes it possible to implement this in a real time application. It is shown through theoretical arguments and flight-testing that this is a viable method for high-speed interpolated range measurements. Standard deviation is 0.75 m over water with only 350 mw of transmitted power at 2600 m.

Watt-level short-length holmium-doped ZBLAN fiber lasers at 1.2 µm.

In-band core-pumped Ho3+-doped ZBLAN fiber lasers at the 1.2 µm region were investigated with different gain fiber lengths. A 2.4 W 1190 nm all-fiber laser with a slope efficiency of 42% was achieved by using a 10 cm long gain fiber pumped at a maximum available 1150 nm pump power of 5.9 W. A 1178 nm all-fiber laser was demonstrated with an output power of 350 mW and a slope efficiency of 6.5%. High Ho3+ doping in ZBLAN is shown to be effective in producing single-frequency fiber lasers and short-length fiber amplifiers immune from stimulated Brillouin scattering.

Binary phase shift keying on orthogonal carriers for multi-channel CO2 absorption measurements in the presence of thin clouds.

A new modulation technique for Continuous Wave (CW) Lidar is presented based on Binary Phase Shift Keying (BPSK) using orthogonal carriers closely spaced in frequency, modulated by Maximum Length (ML) sequences, which have a theoretical autocorrelation function with no sidelobes. This makes it possible to conduct multi-channel atmospheric differential absorption measurements in the presence of thin clouds without the need for further processing to remove errors caused by sidelobe interference while sharing the same modulation bandwidth. Flight tests were performed and data were collected using both BPSK and linear swept frequency modulation. This research shows there is minimal or no sidelobe interference in the presence of thin clouds for BPSK compared to linear swept frequency with significant sidelobe levels. Comparisons between of CO(2) optical depth Signal to Noise (SNR) between the BPSK and linear swept frequency cases indicate a 21% drop in SNR for BPSK experimentally using the instrument under consideration.